Esp8266 ,
Esp8266Mod01
cette page concerne le modèle
Esp8266Mod01!
20250804
il existe un modèle avec accès au 8 pins pour bricolage
https://fr.aliexpress.com/item/1005008635345570.html
dit ne demande pas de manipulation, entre automatiquement en download ...
20250808: ok download, conso a vide 9 mA
GAFFE! si j'arrache l'UART, pas de 3.3V sur le pied jaune mais toujour sur broche centrale du regulateur
autre essai sur un vieux support (sans inter prog ni reset ) OK 0 mA
201891020: entre 1 et 2 €.
empiriquement l'
ArduinoIde? peut essayer de télécommander le chargement:
- utilise les pins RTS (reset) et DTR (GPIO0) mais encore faut-il qu'ils soient pris en compte.
- utilise une seule ligne mais avec un délai (créé par un condensateur) pour la ligne Gpio0?
sinon, d'autres matériels peuvent ignorer ce procédé et choisissent de manipuler l'état des
Gpio0? et Rst
plan:
- avec/sans condensateur
- avec ou sans bouton Reset
- avec ou sans switchGpio0
- chip Ttl2Usb intégré
- GAFFE EVITER SUPPORT POUR NRF24L01 : même aspect mais brochage incompatible
à distribuer entre:
un qui est gravé 3V3, (par opposition au jaune biffé ci dessus):
1.46 €:
https://fr.aliexpress.com/item/Developent-Board-Adapter-USB-to-ESP8266-Serial-Wireless-Wifi-Module/32782943678.html
commandé le 20170214
pas usb, paés inter de programmation, pas accès aux 8 pins!
1.04 €:
https://fr.aliexpress.com/item/ESP8266-Serial-WiFi-Wireless-ESP-01-Adapter-Module-3-3V-5V-Compatible-For-Arduino/32764173835.html
gaffe: la suite ne dit pas grand chose de la possibilité/nécessité d'ajouter un bouton pour mettre
Gpio0? à gnd avant de programmer, ni de gérer le bouton reset
en d'autres termes, possible que "nu" il ne permette que la communication, pas la programmation
un où l'on voit le switch:
20181013 4.5 € avec un
Esp8266, donc environ 3 € le programmer
http://www.dx.com/fr/p/open-smart-esp8266-wi-fi-transceiver-module-usb-to-esp-01-adatper-452227#.WJ3sFjjcwrE
seul: 3.51 €:
http://www.dx.com/fr/p/open-smart-usb-to-esp8266-esp-01-wi-fi-adapter-module-w-ch340g-driver-452226
2.45:
http://www.volumerate.com/product/open-smart-usb-to-esp8266-esp-01-wi-fi-adapter-module-w-ch340g-driver-844452226
un compatible
BreadBoard: 2.50 €:
http://www.ebay.fr/itm/ESP01-ESP8266-USB-node-RGB-led-adapter-relay-driver-Arduino-nodemcu-elua-/321748345421
(avec bouton GPIO0 à la masse)
pas épuisé:
http://www.ebay.ie/itm/152133222626
the winner is:
à l'unité: 1.34 € chez ebay: http://www.ebay.fr/itm/1PCS-ESP01-Programmer-Adapter-UART-GPIO0-ESP-01-Adaptateur-ESP8266-USB-NEW-/222121082897
mais le vendeur est absent!
il dit: >
This moduel is an USB adpater / programmer for ESP8266 moduels of type ESP-01. It is conveniently fitted with a 2x4P 2.54mm female header to plug the ESP01 (according to illustration picture 2) and configure or run it right away. A large 1000μF cap will help getting a steady 5.0V VCC from the USb bus and and jumper (on the right of the 2x4P header) will help configuring the GPIO0 line according needs. The module is based on the USB-UART bridget CH340 from WCH which is compatible with all platforms.
Nota : for an usage with Arduino ESP8266 platform and Arduino IDE it is necessary to switch manually the GPIO0 state for working mode, in order to get a fully automatic upload it is most likely possible, for a very limited effort, to assign an unused control line from CH340 to driver the GPIO0 line (probably at the cost of a necessary logic inversion), refer to the CH340 datasheet and most important to the NodeMCU V0.9 which use the CH340 and already implements this solution, the schematic is open source and easily available.
Package includes:
commentaire sur cette solution:
http://www.esp8266.com/wiki/doku.php?id=all-in-one-esp-usb-converter
sinon, lisez la suite:
ci dessous un empilage incertain, nécessite de maintenir un bouton lors du reboot pour le programmer
GAFFE: pour le modèle 01 faudrait aussi un support de production ? sinon branchement direct sur les 8 pins, ça craint!
voir projet concurrent:
Esp8266Mod1Cableprogrammation
hors de prix: 3$: GAFFE AU PORT breadboard adapter:
https://www.tindie.com/products/rajbex/esp8266-breadboard-adapter
passif: 5$: livré,
http://fr.aliexpress.com/item/Breadboard-adapter-for-ESP8266-Serial-to-WiFi-transceiver/32281305443.html
1$50: (port ?)
http://mklec.com/components/circuit_boards_pcbs/ESP8266-NRF24L01-module-breadboard-adapter-pcb
altrnative pour le planter dans un breadBoard: 1.05 €:
https://fr.aliexpress.com/item/Free-Shipping-ESP8266-ESP-01-ESP-01S-Breadboard-Adapter-PCB-for-Serial-Wifi-Transceiver-Network-Module/32769904386.html
soluce:
meilleur choix:
https://fr.aliexpress.com/item/ESP01-Programmeur-Adaptateur-UART-GPIO0-ESP-01-Adaptaterr-ESP8266-CH340G-USB-ESP8266-S-rie-Sans-Fil/32884779462.html