OlinuxIno
piste debian:
https://github.com/OLIMEX/OLINUXINO/blob/master/SOFTWARE/iMX233/DEBIAN/DEBIAN-BUILD.txt
pas explorée
carte origine/copie à déterminer modifiée,
montée dans vostro1720 en boot knoppix 7
apparait comme /dev/mmcblk0
ls imges se montent sans souci:
sudo mount /media/po fichier image
inventaire:
originale, 2 Go, 10 €,
égarée
microsD Hc 4Gb Kingston
à inventorier
autre
à décrire dès que démontée
!
4 Go
achat 4 € par amazon
fait quelques modifs (invite, etc, ...)
deux partitions:
type 53, 15000 blocs
type: 83, 1910015 blocs
NOTE: 1.8 Go non alloués (vus par gparted)
sauvegardé dans image: maxell 600 /olisd2/sauve1/quelquesmodifs par
dd bs=512000 vitesse 3Mo/' soit sans doute 30'.
à 10 , 1 Go, débit tombé à 2 Go/'; finalement 1.5 Mb/"
feuille de route:
faire aussi sauvegarde de chaque partition,
sauvegardé partiton 1 dans image: maxell 600 /olisd2/sauve1/quelquesmodifsP1 par dd bs=512000 vitesse 6mb/".
sauvegardé partiton 2 dans image: maxell 600 /olisd2/sauve1/quelquesmodifsP2 par dd bs=512000 vitesse 6mb/"
(pas d'explication sur le meilleur débit?)
et essayer de monter les images sous knoppix en lecture
build1
suivant: https://github.com/Freescale/fsl-community-bsp-platform/blob/master/README
- ok kurl est là
- faut créer dossier ~/bin
- ajouter option "unsecute -k
- ajouter option "unsecute -k
- utilise ~/bin/repo au ieu de repo
se termine en erreur:
knoppix@Microknoppix:/media/sdb1/olisd2/build1/fsl-community-bsp$ ~/bin/repo init -u https://github.com/Freescale/fsl-community-bsp-platform -b denzil
Get https://gerrit.googlesource.com/git-repo
error: while accessing https://gerrit.googlesource.com/git-repo/info/refs
fatal: HTTP request failed
knoppix@Microknoppix:/media/sdb1/olisd2/build1/fsl-community-bsp$
message à la liste:
Hello,
I use OlinuxInoMaxi, it runs with the sdcard sold by Olimex.
Now I am learning to build a new one.
My workstation is Knoppix 7.0
I follow:
https://github.com/Freescale/fsl-community-bsp-platform/blob/master/README
I have an error while downloading BSP source:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
knoppix@Microknoppix:/media/sdb1/olisd2/build1/fsl-community-bsp$ ~/bin/repo init -u https://github.com/Freescale/fsl-community-bsp-platform -b denzil
Get https://gerrit.googlesource.com/git-repo
error: while accessing https://gerrit.googlesource.com/git-repo/info/refs
fatal: HTTP request failed
knoppix@Microknoppix:/media/sdb1/olisd2/build1/fsl-community-bsp$
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
questions:
- is-it a right way to start building a scratch SdCad??
best regards
PO.
essai direct de la page,
fzut avoir ouvert une session sur google, lmich94 n'estpas satifaisant.
autre piste (build2):
https://github.com/radolin/meta-olinuxino/blob/master/README
bitbahe
bitbake core-image-minimal
Pseudo is not present but is required, building this first before the main build
ERROR: Unable to determine endianness for architecture 'INVALID'| ETA: --:--:--
ERROR: Please add your architecture to siteinfo.bbclass
ERROR: Unable to parse /media/sdb1/olisd2/build2/oe-core/meta/recipes-support/taglib/taglib_1.6.3.bb: Exited with "1"
ERROR: Unable to determine endianness for architecture 'INVALID'
ERROR: Please add your architecture to siteinfo.bbclass
ERROR: Unable to determine endianness for architecture 'INVALID'
ERROR: Please add your architecture to siteinfo.bbclass
ERROR: OE-core's config sanity checker detected a potential misconfiguration.
Either fix the cause of this error or at your own risk disable the checker (see sanity.conf).
Following is the list of potential problems / advisories:
Please set a valid MACHINE in your local.conf or environment
Please install the following missing utilities: diffstat,texi2html,chrpath
Toolchain tunings invalid:
No tuning found for default multilib.
ERROR: Execution of event handler 'check_sanity_eventhandler' failed
ERROR: Command execution failed: Exited with 1
Summary: There were 10 ERROR messages shown, returning a non-zero exit code.
Ooops:
olinuxino n'est pas connu dans meta/classes/siteinfo.bbclasses
(le messag d'erreur provient de ce ficioer)
disparait sui je choisis Qemuxxx dans local.conf
sanity checker demande diffstat texi2html et chrpath
pas réusi à ignorer sanity checker
apt-get ne connait pas dffstat
apres apt-get update, il est là! et les deux autres aussi.
relancé avec MACHIN ?= "qemux86",
ça roule
feuille de route; forger olinuxino